Search found 29 matches

by mikeh9
Mon Apr 09, 2018 12:50 pm
Forum: Software Development
Topic: Driver and USBTraq Alternatives for Linux systems (or ROS packages)
Replies: 4
Views: 1625

Re: Driver and USBTraq Alternatives for Linux systems (or ROS packages)

The minimum offset sets the vertical positions of the bottom anchors for the automatic anchor positioning mode. Therefore it will also affect the 10006 command which are the anchor positions and 10001 command which contains the tag position. Commands 10002 and 10003 will not be affected by the minim...
by mikeh9
Wed Apr 04, 2018 1:02 pm
Forum: Software Development
Topic: Driver and USBTraq Alternatives for Linux systems (or ROS packages)
Replies: 4
Views: 1625

Re: Driver and USBTraq Alternatives for Linux systems (or ROS packages)

We use STM32F4 chips. STMicroelectronics only provides PC based virtual comm port drivers, but by searching the web, I find quite a few people using these chips with Ubuntu. As an example, see the following link: https://electronics.stackexchange.com/questions/283852/stm32-usb-cdc-firmware-to-autode...
by mikeh9
Wed Feb 21, 2018 1:56 pm
Forum: Hardware Installation
Topic: Anchor Auto-Calibration
Replies: 4
Views: 1934

Re: Anchor Auto-Calibration

What is your email address? I can email you the NDA and then get you access.

I suggest you start with USBTraq, then use serial commands to automate your application. This will save you a ton of time.

Its hard to predict the accuracy of a very small space. The ideal testing space is around 6m x 6m.
by mikeh9
Tue Feb 20, 2018 5:51 pm
Forum: Hardware Installation
Topic: Anchor Auto-Calibration
Replies: 4
Views: 1934

Re: Anchor Auto-Calibration

1. Do you have a 4 anchor system or an 8 anchor system? The number of anchors needs to be selected using USBTraq connected to the master anchor. 2. The system has to be setup correctly on the Anchor Positions tab. Please refer to guide and video on the support page for anchor positioning. 3. All the...
by mikeh9
Mon Nov 27, 2017 2:28 pm
Forum: Basic Troubleshooting
Topic: Setting up Anchor / Tag IDs via using USBTraq and jumpers
Replies: 1
Views: 1645

Re: Setting up Anchor / Tag IDs via using USBTraq and jumpers

As of firmware 3.XX, anchor addresses can also be set using USBTraq-Settings. Simply change device ID in the upper left corner and then click on Write to Device. In order for this to work, all physical address jumpers must be removed from the anchor.
by mikeh9
Mon Nov 27, 2017 2:08 pm
Forum: Hardware Installation
Topic: Anchor Addresses
Replies: 1
Views: 1234

Re: Anchor Addresses

As of firmware 3.XX, anchor addresses can also be set using USBTraq-Settings. Simply change device ID in the upper left corner and then click on Write to Device. In order for this to work, all physical address jumpers must be removed from the anchor.
by mikeh9
Fri Nov 03, 2017 2:57 pm
Forum: Software Development
Topic: Digital Tag I/O
Replies: 1
Views: 1523

Re: Digital Tag I/O

Attached is the wiring diagram. You will want to use the last three outputs. These outputs put out 3.3VDC when set to 1 and put out 0V when set to 0. They are not designed to drive loads more than 10mA or inductive type loads. They are signal outputs. They can drive a low power LED though. Also atta...
by mikeh9
Fri Sep 08, 2017 7:57 pm
Forum: Programming Devices
Topic: How to program devices
Replies: 0
Views: 1566

How to program devices

Information will be found here soon.
by mikeh9
Fri Sep 08, 2017 7:56 pm
Forum: Troubleshooting / Using Terminal
Topic: Using Terminal
Replies: 0
Views: 1585

Using Terminal

Information will be found here soon.
by mikeh9
Fri Sep 08, 2017 7:50 pm
Forum: Setting Up Anchors
Topic: Selecting the anchor device ID.
Replies: 0
Views: 1640

Selecting the anchor device ID.

Information will be found here soon.

Go to advanced search